top
Articles
  • OpenAccess
  • Evaluation of Geometric Quality of Weld Beads in the Joining of Carbon Steel Pipelines with Single Pass  [CPME 2013]
  • DOI: 10.4236/jpee.2013.17001   PP.1 - 5
  • Author(s)
  • José Eduardo Silveira Leal, Thonson Ferreira Costa, Rosenda Valdés Arencibia
  • ABSTRACT
  • This work presents the uncertainty evaluation associated with the measurement of linear parameters that define the weld geometry, specifically the width, using a profile projector, in order to meet the current technical standards. The following steps were proposed and implemented: identification of linear parameters that define the weld geometry; identification and study of variables that affect the measurement of these parameters; the adoption of the mathematical model to estimate the uncertainty; planning and execution of experiments for data collection, calculation of uncertainty and, finally, analysis and discussion of the results. Through the results analysis it was concluded that the weld in overhead position produces the lowest front bead width values and the vertical weld produces the largest width values. The expanded uncertainty values were between 0.016 mm and 0.075 mm for all measurements, and the overhead position showed, on average, the highest values.

  • KEYWORDS
  • Welding; Weld Bead Geometry; Profile Projector; Uncertainty
  • References
  • [1]
    Soldagem & Brasagem, “Historia da Soldagem,” 2012.
    http://soldagemebrasagem.blogspot.com.br/2012_03_22_archive.html
    [2]
    P. J. Modenesi, P. V. Marques and D. B. Santos, “Introdução à Metalurgia da Soldagem,” Belo Horizonte, Brasil, 2012, p. 209.
    http://demet.eng.ufmg.br/wp-content/uploads/2012/10/metalurgia.pdf
    [3]
    A. R. Valdés, E. M. Díaz Cédre, A. C. Crespo and A. Piratelli Filho, “Incerteza na Medição dos Parametros Geométricos do Cordão de Solda,” Soldagem e Inspeção, Vol. 16, No. 1, 2011, pp. 62-70.
    http://dx.doi.org/10.1590/S0104-92242011000100008
    [4]
    Associação Brasileira de Normas Técnicas, NBR ISO/ IEC 17025: “Requisitos Gerais para Competência de Laboratório de Ensaios e Calibrações,” Rio de Janeiro, Brasil, 2005, p. 20.
    [5]
    R. A. Valdés and J. R. S. Ribeiro, “Incerteza na Medição da Largura de Cordões de Solda,” Soldagem e Inspeção, Vol. 14, No. 3, 2009, pp. 263-269.
    [6]
    C. M. D. Starling, P. J. Modenesi and T. M. D. Borba, “Caracterização do Cordão na Soldagem FCAW com um Arame Tubular (“MetalCored”),” Soldagem e Inspeção, São Paulo, Vol. 16, No. 3, 2011, pp. 285-300.
    [7]
    R. A. Valdés, A. C. Crespo, A. Piratelli-Filho and E. M. Díaz Cedre, “Aplicación de Criterios Metrológicos a la Evaluacióndel Recargue por Soldadura,” São Luís, Maranhão, Brasil, CONEM, 2012, p. 10.
    [8]
    J. S. Kim, L. S. Kim, J. H. Lee and S. M. Jung, “An Experimental Study on the Prediction of Back-Bead Geometry in Pipeline Using the GMA Welding Process,” International Scientific Journal, Vol. 49, No. 1, 2011, pp. 53-61.
    [9]
    Associação Brasileira de Normas Técnicas, NBR NM ISO 1: “Temperatura Padrão de Referência para Medições Industriais de Comprimento,” Rio de Janeiro, Brasil, 1997, p. 2.
    [10]
    ISO TAG 4/WG 3, “Guide to the Expression of Uncertainty in Measurement,” Geneva, Switzerland, 2008, p. 131.

Engineering Information Institute is the member of/source content provider to

http://www.scirp.org http://www.hanspub.org/ http://www.crossref.org/index.html http://www.oalib.com/ http://www.ebscohost.com/ http://www.proquest.co.uk/en-UK/aboutus/default.shtml http://ip-science.thomsonreuters.com/cgi-bin/jrnlst/jlresults.cgi?PC=MASTER&Full=journal%20of%20Bioequivalence%20%26%20Bioavailability http://publishers.indexcopernicus.com/index.php